Skip to content
Port Colborne Plumber

Guides

Keeping pipes from freezing in a Port Colborne winter

How to protect your pipes through Port Colborne's long frost season, what to do first if one freezes or bursts, and how to find and test your main water shut-off before you need it.

7 min read Updated November 17, 2026.

Keeping pipes from freezing in a Port Colborne winter

If a pipe has already burst, start here. Turn off the main water valve where the water line comes into the house. Then open the lowest cold tap to drain what is left in the pipes. If water is anywhere near an outlet, a light fitting or the electrical panel, keep away from it and turn off the breaker for that area only if you can reach the panel from a dry floor. Those are the two things that matter in the first few minutes. Everything else in this guide can wait until the water has stopped.

How long is the frost season in Port Colborne?

Longer than most people expect. Environment Canada's 1981-2010 climate normals for the Port Colborne station show about 121 days a year with a low at or below 0 °C, and about 23 days a year colder than -10 °C. On average the first fall frost comes around October 26 and the last spring frost around April 25. That's six months when a pipe in a cold spot can freeze, and the hard freezes tend to come in short spells. A pipe that got through December can still freeze on one bitter night in February.

Pipes rarely freeze where it's warm. They freeze where cold air gets in: along an outside wall, in a crawl space, in an attached garage, under a sink on an outside wall, or where the water line comes through the foundation.

Which pipes are most at risk in my kind of house?

The answer depends a good deal on when your house was built.

  • **Older houses in the original town and Humberstone.** Houses from before the war, including the old vacation homes still standing on Tennessee Avenue, often have galvanized steel water lines and sometimes still have lead service lines. Many have been added onto over the years, and a pipe that was rerouted into an addition, a back porch or an enclosed crawl space can end up with no heat around it. Galvanized pipe also corrodes from the inside, so an old pipe that freezes is more likely to split than to survive.
  • **Post-war houses around Barrick Road and Olga Drive.** These houses usually have copper water lines. Copper tolerates a mild freeze better than old steel, but long runs along a cold outside wall, or under a kitchen sink on a north wall, are the usual trouble spots. A freeze can also show up weeks later as a pinhole leak.
  • **Newer subdivisions such as Westwood Estates, Mapleview, Rosedale Estates and Millar's Crossing.** Plastic water lines give a little more when they freeze, but they can still split. In these houses the weak points are outdoor hose taps, lines in or next to an attached garage, and any pipe running near a garage ceiling below a bedroom.

How do I keep pipes from freezing?

Most of this takes an afternoon in October and costs little.

  • **Shut off and drain outdoor taps.** Find the shut-off valve inside the house for each outdoor tap, close it, open the outdoor tap to let it drain, and disconnect the hose. A hose left attached holds water in the tap, and that's one of the most common freezes.
  • **Seal the drafts.** Look where pipes and cables come through the foundation and the rim joist, and fill the gaps. Cold air coming through a small gap onto a pipe causes more frozen lines than low room temperature does.
  • **Insulate exposed pipes.** Foam pipe sleeves are cheap and easy to fit on pipes in crawl spaces, unheated rooms and along outside walls in the basement.
  • **Keep the heat on.** Keep the house heated even when you're away. A setting that feels a bit cool to you is still enough for the pipes.
  • **On the coldest nights, help the pipes that worry you.** Open the cabinet doors under sinks on outside walls so warm air can reach the pipes. Leave a thin, steady trickle running from the tap at the end of a line that has frozen before. Water that's moving is much slower to freeze.
  • **Leaving for more than a few days?** Have someone check the house regularly. For a longer trip, think about turning off the main valve and draining the lines. Check with your insurer, since some policies have conditions for houses left empty in winter.

What does a frozen pipe look like, and can I thaw it myself?

The usual sign is a tap that gives a trickle or nothing at all, while other taps run normally. A frozen section may also have frost on it or feel much colder than the pipe next to it.

You can usually thaw a pipe you can reach yourself, as long as it hasn't split:

  • Open the tap the pipe feeds so that water can flow as it melts.
  • Warm the pipe slowly with a hair dryer or a heating pad, starting near the tap and moving back toward the frozen section.
  • Never use an open flame, a torch or a propane heater. Old pipe and the wood framing around it can catch fire, and heating the pipe too fast can burst it.

When the water comes back, look along the pipe for drips. A split often doesn't leak until the ice melts.

Leave it for a plumber if you can't reach the frozen section, if it's inside a finished wall or ceiling, or if no tap in the house is running. If the whole house has no water, the freeze may be in the service line where it comes in. Your part of that line runs from the property line to the house.

What should I do first when a pipe bursts?

Go in this order and take your time:

1. **Turn off the main water valve.** The next section explains how to find it.
2. **Drain the system.** Open the lowest cold tap in the house, and a few taps upstairs, so the water in the pipes runs out somewhere harmless.
3. **Think about electricity.** If water has reached outlets, fixtures or the panel, don't stand in it to reach the breaker. Leave it and tell the plumber when you call.
4. **If it's a hot water pipe,** also close the cold supply valve on top of the water heater.
5. **Move what you can, then take photos** of the pipe, the water and anything damaged for your insurer.
6. **Call a plumber.** Once the water is off, the rush is over.

Where is my main water shut-off valve?

In most Port Colborne houses the main valve is in the basement, on the wall facing the street, where the water line comes through the floor or the foundation. It is usually beside the water meter, on the house side. In houses without a basement, check the crawl space entrance, a utility room or the cupboard under the stairs.

You'll find one of two types:

  • A round wheel handle (a gate or globe valve), common in older houses. Turn it clockwise until it stops.
  • A lever handle (a ball valve), common in newer houses. A quarter turn closes it. When the lever is crossways to the pipe, the valve is closed.

There's also a valve at the property line, usually under a small cover in the lawn or near the sidewalk. The City of Port Colborne is responsible for the line from the main to the property line, so leave that valve to the City.

How do I test the main shut-off before I need it?

Do this on a calm day, not during a leak:

1. Turn the valve off.
2. Open a cold tap on the main floor. The flow should slow and then stop within a minute or so.
3. Turn the valve back on slowly and close the tap.
4. Check the valve stem for a drip over the next hour.

If an old wheel valve won't turn, don't force it with a wrench, because a seized valve can snap. If it turns but the water keeps running, or it drips at the stem afterwards, the valve needs replacing. Plan that before winter. Tag the valve so anyone in the house can find it.

Will the repair need a permit, and is there help with an old line?

A like-for-like repair to a burst section is usually simple. Under Ontario's Building Code Act, installing or materially altering plumbing generally needs a permit from the municipality. The City's building department can tell you whether your job does.

If your water line from the property line in keeps freezing, or is old galvanized or possibly lead pipe, the City of Port Colborne offers grants to owners of existing homes towards replacing the private water and sewer lines. See plumbing repairs for what that work involves.

If a pipe has frozen or burst and you'd like help, our emergency plumber page explains how to reach us.

Still have a question?